HSKSIC10180120 Silicon thermal management, therma plane, Laser diode submounts Si - 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks - High heat transfer rate, High thermal conductivity Silicon heat sinks and stand offs manufactured by US Microwaves HSKSIC10180120,thermal management,therma plane,Laser diode submounts,Heat sinks, stand offs, bonding islands, isolated, electrically conductive,aluminum nitride, beryllium oxide,silicon, copper,heat transfer rate,thermal conductivity,thermal contact,thermal resistance,thermal shock,microwave hybrid circuits,GaAs microwave active devices,solid state power amplifiers HSKSIC10180120 Silicon thermal management, therma plane, Laser diode submounts Si - 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks - High heat transfer rate, High thermal conductivity Silicon heat sinks and stand offs manufactured by US Microwaves HSKSIC10180120,thermal management,therma plane,Laser diode submounts,Heat sinks, stand offs, bonding islands, isolated, electrically conductive,aluminum nitride, beryllium oxide,silicon, copper,heat transfer rate,thermal conductivity,thermal contact,thermal resistance,thermal shock,microwave hybrid circuits,GaAs microwave active devices,solid state power amplifiers US MICROWAVES 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks Advanced Microwave Components HSKSIC10180120 FEATURES APPLICATIONS Si Electrically Conductive Heat Sink High heat transfer rate High thermal conductivity Very good thermal contact Very good thermal shock resistance Microwave hybrid circuits Mount for GaAs microwave active devices Solid state RF power amplifiers 180x120 mils, 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120 HSKSIC10180120 Silicon Electrically Conductive Heat Sink PRODUCT DESCRIPTION AND SHORT APPLICATION NOTE The HSKSIC10180120 series of microwave 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks TECHNOLOGY DESCRIPTION: SEMICONDUCTOR - THIN FILM MANUFACTURING HSKSIC10180120 Silicon Electrically Conductive Heat Sink ELECTRICAL/MECHANICAL CHARACTERISTICS PARAMETER SYMBOL VALUE UNITS Length L 180 mils Width W 120 mils Thickness T 10 mils Thermal Resistance Rth 0.12 K/W Thermal Conductivity k 8.33E+00 W/K DC Resistance DCR 0.42 mΩ ONLY Proper die handling equipment and procedures should be employed. Stresses beyond listed absolute maximum ratings may cause permanent damage to the device. HSKSIC10180120 Silicon Electrically Conductive Heat Sink GENERAL DIE INFORMATION Substrate Thickness [mils] Size [mils] Case style Si [Silicon] 10±0.5 180x120±2 1812 Frontside metal Backside metal The standard front side metallization (BD0 - compatible with AuSn,AuGe die attach) is min 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands >30 min at 400°C in air without loss of adhesion. Other available metallization schemes are -BD1: Ti/Pd/Au compatible with AuSn,AuGe -BD2: Ti/Pt/Au compatible with AuSn,AuGe -BD3: Ti/Ni/Au compatible with Soft Solder SAC -BD4: Ti/Pt/AuSn compatible with AuSn eutectic -BD5: Ti/Ni/Sn compatible with Soft Solder SAC. Custom metallization is available for special orders. The standard back side metallization (BD0 - compatible with AuSn,AuGe die attach) is min 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands >30 min at 400°C in air without loss of adhesion. Other available metallization schemes are -BD1: Ti/Pd/Au compatible with AuSn,AuGe -BD2: Ti/Pt/Au compatible with AuSn,AuGe -BD3: Ti/Ni/Au compatible with Soft Solder SAC -BD4: Ti/Pt/AuSn compatible with AuSn eutectic -BD5: Ti/Ni/Sn compatible with Soft Solder SAC. Custom metallization is available for special orders. 180x120 mils, 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120 All US Microwaves Silicon Electrically Conductive Heat Sink products are available in die form. Typical delivery for die products is 2-3 weeks ARO. For Custom designs, delivery is 3-4 weeks ARO. Certain items may be available from stock. Inventory is periodically updated. All devices for chip and wire applications are 100% tested, visual inspected and shipped in waffle packs (WP). Silicon Electrically Conductive Heat Sink STANDARD PRODUCTS ORDERING INFORMATION Silicon Electrically Conductive Heat Sink STANDARD PRODUCTS T L W METAL DIE ATTACH US MICROWAVES PART NUMBER WAFFLE PACKS MIN. QTY U/P [$] ORDER [mils] 10 180 120 TiW/Au AuSi, AuGe, epoxy HSKSIC10180120-BD0 -WP RFQ Ti/Pd/Au AuSn, AuGe HSKSIC10180120-BD1 -WP RFQ Ti/Pt/Au AuSn, AuGe HSKSIC10180120-BD2 -WP RFQ Ti/Ni/Au Soft Solder SAC HSKSIC10180120-BD3 -WP RFQ Ti/Pt/AuSn AuSn eutectic HSKSIC10180120-BD4 -WP RFQ Ti/Ni/Sn Soft Solder SAC HSKSIC10180120-BD5 -WP RFQ 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120: Products sold for space, military or medical applications, element evaluation and/or level K or S qualification are subject to minimum order levels to be established on a case by case basis. For any special applications, die level KGD qualification requirements, different packaging or custom configurations, contact sales department. HSKSIC10180120 Silicon Electrically Conductive Heat Sink INSTANT QUOTE US Microwaves P/N Quantity E-mail ORDERING: Silicon Electrically Conductive Heat Sink may be ordered on line HERE. A copy of the order along with an order confirmation receipt is issued instantly for all orders placed on line. On line Orders have to be verified, accepted and acknowledged by US Microwaves sales department in writing before, becoming non cancelable binding contracts. DELIVERY: Typical delivery for 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks Si SHIPPING/PACKAGING: All 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks SAMPLES: Samples of 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks GUARANTEED SUPPLY! US Microwaves guarantees continuous supply and availability of all Silicon Electrically Conductive Heat Sink standard products provided minimum order quantities are met. U.S. Microwaves has made every effort to have this information as accurate as possible. However, no responsibility is assumed by U.S. Microwaves for its use, nor for any infringements of rights of third parties which may result from its use. U.S. Microwaves reserves the right to revise the content or modify its product line without prior notice. U.S. Microwaves products are not authorized for and should not be used within support systems which are intended for surgical implants into the body, to support or sustain life, in aircraft, space equipment, submarine, or nuclear facility applications without the specific written consent of U.S. Microwaves. Home Product Tree Tech. Support PDF Request Quote Inventory Place Order Contact sales

 
 
US MICROWAVES   10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks
Advanced Microwave Components   HSKSIC10180120
 
 

FEATURES
APPLICATIONS
Si Electrically Conductive Heat Sink
High heat transfer rate
High thermal conductivity
Very good thermal contact
Very good thermal shock resistance
Microwave hybrid circuits
Mount for GaAs microwave active devices
Solid state RF power amplifiers
180x120 mils, 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120

HSKSIC10180120 Silicon Electrically Conductive Heat Sink
PRODUCT DESCRIPTION AND SHORT APPLICATION NOTE
The HSKSIC10180120 series of microwave 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks is designed to be used in microwave hybrid circuits. These devices can be used over the full military temperature range -55°C to +125°C. Quality and workmanship is per MIL-S-883. Level B. Devices are 100% visual inspected and packaged in waffle packs.

TECHNOLOGY DESCRIPTION: SEMICONDUCTOR - THIN FILM MANUFACTURING
All thin film microwave products are manufactured using advanced semiconductors and thin film technologies including ultra-stable and self passivating Tantalum Nitride resistors, gold interconnect metallization and reliable MNOS capacitors to achieve excellent uniformity, performance and reliability. Thin film technology is the preferred solution for all applications that require low noise, long term stability and excellent performance at very high frequencies. US Microwaves employs proprietary thin film technologies for deposition of a wide range of resistive films with sheet resistance films from 1Ω/sq to 10,000Ω/sq. All US Microwaves products are available in die form and are ideal for high reliability hybrid and multi chip module applications.

HSKSIC10180120 Silicon Electrically Conductive Heat Sink
ELECTRICAL/MECHANICAL CHARACTERISTICS
PARAMETER SYMBOL VALUE UNITS
Length L 180 mils
Width W 120 mils
Thickness T 10 mils
Thermal Resistance Rth 0.12 K/W
Thermal Conductivity k 8.33E+00 W/K
DC Resistance DCR 0.42
ONLY Proper die handling equipment and procedures should be employed. Stresses beyond listed absolute maximum ratings may cause permanent damage to the device.

HSKSIC10180120 Silicon Electrically Conductive Heat Sink
GENERAL DIE INFORMATION
Substrate Thickness [mils] Size [mils] Case style
Si [Silicon] 10±0.5 180x120±2 1812
Frontside metal Backside metal
The standard front side metallization (BD0 - compatible with AuSn,AuGe die attach) is min 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands >30 min at 400°C in air without loss of adhesion. Other available metallization schemes are -BD1: Ti/Pd/Au compatible with AuSn,AuGe -BD2: Ti/Pt/Au compatible with AuSn,AuGe -BD3: Ti/Ni/Au compatible with Soft Solder SAC -BD4: Ti/Pt/AuSn compatible with AuSn eutectic -BD5: Ti/Ni/Sn compatible with Soft Solder SAC. Custom metallization is available for special orders. The standard back side metallization (BD0 - compatible with AuSn,AuGe die attach) is min 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands >30 min at 400°C in air without loss of adhesion. Other available metallization schemes are -BD1: Ti/Pd/Au compatible with AuSn,AuGe -BD2: Ti/Pt/Au compatible with AuSn,AuGe -BD3: Ti/Ni/Au compatible with Soft Solder SAC -BD4: Ti/Pt/AuSn compatible with AuSn eutectic -BD5: Ti/Ni/Sn compatible with Soft Solder SAC. Custom metallization is available for special orders.
180x120 mils, 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120
All US Microwaves Silicon Electrically Conductive Heat Sink products are available in die form. Typical delivery for die products is 2-3 weeks ARO. For Custom designs, delivery is 3-4 weeks ARO. Certain items may be available from stock. Inventory is periodically updated. All devices for chip and wire applications are 100% tested, visual inspected and shipped in waffle packs (WP).

Silicon Electrically Conductive Heat Sink STANDARD PRODUCTS ORDERING INFORMATION

Silicon Electrically Conductive Heat Sink STANDARD PRODUCTS
T L W METAL DIE ATTACH US MICROWAVES
PART NUMBER
WAFFLE
PACKS
MIN.
QTY
U/P
[$]
ORDER
[mils]
10 180 120 TiW/Au AuSi, AuGe, epoxy HSKSIC10180120-BD0 -WP     RFQ
Ti/Pd/Au AuSn, AuGe HSKSIC10180120-BD1 -WP     RFQ
Ti/Pt/Au AuSn, AuGe HSKSIC10180120-BD2 -WP     RFQ
Ti/Ni/Au Soft Solder SAC HSKSIC10180120-BD3 -WP     RFQ
Ti/Pt/AuSn AuSn eutectic HSKSIC10180120-BD4 -WP     RFQ
Ti/Ni/Sn Soft Solder SAC HSKSIC10180120-BD5 -WP     RFQ
10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks HSKSIC10180120: List prices are for standard products, available from stock. List prices for other quantities and tolerances are available on line through Instant Quote. For standard products available from stock, there is a minimum line item order. For custom products please inquire by contacting US Microwaves technical sales. No rights can be derived from pricing information provided on this website. Such information is indicative only, is showed for budgetary use only and subject to change by US MICROWAVES at any time and without notice.
Products sold for space, military or medical applications, element evaluation and/or level K or S qualification are subject to minimum order levels to be established on a case by case basis. For any special applications, die level KGD qualification requirements, different packaging or custom configurations, contact sales department.

STANDARD PRODUCTS AVAILABLE FROM STOCK - ORDERING INFORMATION
USM P/NMIN QTYU/PORDER/RFQSTOCK QTYU/PORDER/RFQ
No part available from stock

HSKSIC10180120 Silicon Electrically Conductive Heat Sink INSTANT QUOTE
US Microwaves P/N Quantity E-mail    
 

ORDERING: Silicon Electrically Conductive Heat Sink may be ordered on line HERE. A copy of the order along with an order confirmation receipt is issued instantly for all orders placed on line. On line Orders have to be verified, accepted and acknowledged by US Microwaves sales department in writing before, becoming non cancelable binding contracts.
DELIVERY: Typical delivery for 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks Si products packaged in waffle packs is 2-4 weeks ARO. For custom designs, delivery is 3-5 weeks ARO. Certain items may be available from stock with delivery up to 1 week.
SHIPPING/PACKAGING: All 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks devices for chip and wire applications are 100% tested, visual inspected and shipped in waffle packs (WP). For larger orders,>10k pc, devices can be shipped on film frame. For smaller quantities, it may vary. For high volume automated assembly, heat sink devices may be supplied as 4" wafers 100% tested, inked and diced on expanded film frame (FF).
SAMPLES: Samples of 10 mils thick gold coated thin film Silicon Electrically Conductive heat sinks are available only for customers that have issued firm orders pending qualification of product in a particular application.

GUARANTEED SUPPLY! US Microwaves guarantees continuous supply and availability of all Silicon Electrically Conductive Heat Sink standard products provided minimum order quantities are met.

U.S. Microwaves has made every effort to have this information as accurate as possible. However, no responsibility is assumed by U.S. Microwaves for its use, nor for any infringements of rights of third parties which may result from its use. U.S. Microwaves reserves the right to revise the content or modify its product line without prior notice. U.S. Microwaves products are not authorized for and should not be used within support systems which are intended for surgical implants into the body, to support or sustain life, in aircraft, space equipment, submarine, or nuclear facility applications without the specific written consent of U.S. Microwaves.


Last updated: September 24, 2010
US MICROWAVES | Tel:408-758-8690 Fax: 408-986-8027 | USMICROWAVES

©1990-2024 US MICROWAVES All rights reserved. No material from this site may be used or reproduced without permission.